力士樂驅動器維修圖解：
F219：Motor Overtemperature Shutdown電機超溫停機。
Description:說明：
Motor temperature has risen to an unacceptable level.
電機溫度已升至不可接受的水平。
As soon as temperature threshold (155°C) is exceeded, the drive will immediately be brought to a standstill as set in the error reaction (P-0-0119, best possible standstill).
一旦超過溫度閾值（155°C），驅動器將立即按照錯誤反應（P-00119，盡可能好的靜止?fàn)顟B(tài)）中的設置靜止。
Cause:原因：
1. The motor was overloaded. The effective torque demanded from the motor was above its allowable continuous torque level for too long.
電動機過載了。電機所需的有效扭矩超過其允許的連續扭矩水平太長時間。
2. Break in line, ground short or short circuit in the motor temperature monitor line
線路斷路、接地短路或電機溫度監測器線路短路
3. Instability in the velocity loop.
速度回路的不穩定性。
Remedy:補救措施：
1. Check the installation of the motor.
檢查電機的安裝情況。
If the system has been in operation for a long time, check to see if thethe operating conditions have changed. (in regards to pollution, friction, moved components, etc.)
如果系統已長時間運行，請檢查操作條件是否發生變化。（關于污染、摩擦、移動部件等）
2. Check wires and cables to the motor temperature monitor for wire breaks, earth short and short circuits.
檢查電機溫度監測器的電線和電纜是否存在斷線、接地短路和短路。
3. Check velocity loop parameters.
檢查速度回路參數。
昆山博世力士樂伺服驅動器維修：HMV01.1E-W0030-A-07-NNNN、HMV01.1E-W0075-A-07-NNNN、HMV01.1E-W0120-A-07-NNNN、HMV01.1R-W0018-A-07-NNNN、HMV01.1R-W0045-A-07-NNNN、HMV01.1R-W0065-A-07-NNNN、HMV01.1R-W0100-A-07-NNNN、HMV02.1R-W0015-A-07-NNNN
轉載請注明出處：上海仰光電子科技專業伺服驅動器維修,伺服電機維修
本文鏈接：http://www.9s7n.com/fuwu/Services_Show26372.htm
伺服驅動器維修 伺服電機維修 觸摸屏維修 變頻器維修
電話：021-50157782
手機：13817011982 微信同號
郵箱：shygdzi@163.com
聯系人：張工
網址：http://www.9s7n.com
【 我們確保修好測試好給客戶�。。。 �
下一篇：沒有了
